Skip to content
JOY TECH — Concrete Polishing Tools logo

PCD Plus Diamond Combo Discs: One-Pass Coating Removal and Profiling

Scroll

PCD Plus Diamond Combo Discs: One-Pass Coating Removal and Profiling

2026-11-18•JTJOY TECH Engineering Team
PCD Plus Diamond Combo Discs: One-Pass Coating Removal and Profiling

Quick Answer

A PCD plus diamond combo disc removes a coating and profiles the concrete in one pass. The PCD (polycrystalline diamond) cutters shatter the coating, while the diamond segments grind the exposed paste. It works on epoxy, glue, thin self-leveler and paint, but not on thick, soft or heavily reinforced coatings. Set a shallow depth, keep the machine moving and follow with a diamond pass if the floor needs a uniform profile.

How a Combo Disc Works

The disc has two kinds of cutting elements: PCD plates that act like small chisels, and diamond segments that grind. The PCD plates sit slightly lower or at the same height as the diamond, depending on the design. As the head rotates, the PCD breaks the coating and the diamond smooths the concrete underneath.

The result is a mixed scratch pattern. On a thin coating, the floor can be ready for a new coating after one pass. On a thick coating, the PCD may chip the edges but leave patches; a second pass or a dedicated PCD tool is needed.

Best Applications

  • Epoxy and polyurethane coatings up to 2-3 mm.
  • Carpet glue, adhesive and mastic residues.
  • Thin self-leveling compound.
  • Paint and thin sealers on concrete.
  • Rough profiling before a repair mortar.

Do not use a combo disc on thick epoxy (5 mm+), soft rubberized coatings, or a floor with unknown asbestos-containing material. Test a small area first and follow local regulations.

Depth and Speed Settings

Start with a shallow depth, about 0.2-0.5 mm, and increase only if the coating is not breaking. Too deep and the PCD plates gouge the concrete; too fast and the PCD skips over the coating. Use a variable-speed grinder and keep the head moving in a steady pattern.

CoatingDepthFollow-up
Thin epoxy0.2-0.3 mmDiamond 30/40 pass
Glue/mastic0.3-0.5 mmDiamond 30/40, then 60/80
Thick epoxySeparate PCD passDiamond after coating is gone
Paint0.2 mmDiamond 60/80

When to Use Separate Passes

If the coating is thick or uneven, a dedicated PCD tool removes it faster and with less diamond wear. The combo disc is a productivity tool for thin coatings, not a replacement for a full coating-removal setup. On a floor with multiple coating layers, use PCD first, then a diamond disc to profile.

If the concrete is soft, the PCD can dig in and leave gouges. Reduce depth and use a combo disc with a flat PCD arrangement, or switch to a diamond-only pass after a light scarify.

Safety and Dust

PCD cutting generates sparks and heat. Use a dust shroud and HEPA vacuum, and keep water away from electrical equipment. Wear eye protection and hearing protection. If the coating may contain asbestos, stop and test before grinding; do not rely on a shop vacuum.

Frequently Asked Questions

Q: Can a combo disc remove 5 mm epoxy?

A: It can start the removal, but a dedicated PCD tool is faster and cheaper on diamond wear. Use combo discs for thin coatings.

Q: Does the combo disc leave a profile ready for epoxy?

A: Usually yes, but check with a straight edge and a profile gauge. A follow-up 30/40 diamond pass gives a more uniform CSP.

Q: Can I use a combo disc on a hand-held grinder?

A: Small combo cup wheels exist, but control is harder. Use a floor grinder for full rooms and a hand-held tool for edges.

Q: Why does the disc spark?

A: PCD cutting through hard coating or aggregate generates heat. Reduce depth, increase speed and use dust extraction.

Conclusion

Combo discs are a one-pass tool for thin coatings, not a universal stripper. Test the coating, set a shallow depth, and follow with a diamond pass for a uniform profile. JOY TECH supplies WerkMaster PCD tooling and diamond trapezoid discs for two-step coating removal.

Products used in this guide

Need this tool for your job?

MOQ 1 · 7–30 days by order quantity · FOB & CIF · free sample on request

Get a factory quote

Share this article

Author & Manufacturer

Written and reviewed by JOY TECH - an SGS & BV audited, CE/RoHS certified diamond tools manufacturer founded in 2004, exporting to 50+ countries.

Quality & Compliance

Our factory and quality management system are audited by SGS and Bureau Veritas. Products meet CE/RoHS requirements and every piece is 100% inspected before packing.

Verified Certificates

  • • SGS Audited Supplier — Report No. QIP-ASI227442 & QIP-ASR247051
  • • Bureau Veritas Verified — Report No. MIC-ASR257059
  • • CE & RoHS Certificate of Conformity — No. CS240925001HRZ

Request a Factory Quote

Average response time: under 24 hours

Or WhatsApp: +86 185 5928 2197 · [email protected]

FAQ

GET A QUOTEWhatsApp